New customers get 15% off your service fee only, until August 31st, code SUMMER!

Welcome to jvpgunsmith.com
Home
Services
Cost Estimates
Shop Policies
About Me
Welcome to jvpgunsmith.com
Home
Services
Cost Estimates
Shop Policies
About Me
More
  • Home
  • Services
  • Cost Estimates
  • Shop Policies
  • About Me

  • Home
  • Services
  • Cost Estimates
  • Shop Policies
  • About Me

Cost Estimates

My standard shop rate is $65.00 per hour.


It is almost impossible to generate a complete and all inclusive list of the myriad individual repairs and services that a gunsmith can perform or a firearm can require. Just because what you are needing to have done doesn’t appear below, does not mean that I can’t perform that service for you! Very few services can be quoted as a fixed cost…each gun is different and how long the repair takes or the need for parts varies.  


As a general rule, firearms repairs are started in the order they are logged in, and I give clients an estimate of what the current backlog is when a firearm is brought in. I typically have 4 -6 guns in the process of repair at any given time, so rarely can I drop everything and repair an incoming firearm unless the repair is extremely simple and parts are in hand. Services such as re-blueing, stock refinishing, restocking and bedding take considerably longer to complete…I make clients aware of this when the firearm is checked in. There are some things you just do not rush!

Cleaning

  • Standard Inspect, Clean and Oil (1) – $65
  • Full Disassemble, Detailed Clean and Oil (2) –  $85
  • Barrel Detail Only (for firearms that have extensive fouling/ rust in barrel/receiver) (3) – $65
  • Conservation Clean, Inspect, Repair, Protect (4) –  Beginning at $130


1.  This is the standard charge for firearms requiring inspections for repair. In many cases, cleaning remedies the malfunction. Note: on truly filthy, gummed up actions where the cause of malfunction cannot be determined, an additional $20 charge is assessed.


2.  Firearms are disassembled completely (except for manufacturer permanent assemblies), cleaned of all grime, residues and surface rust, each part is inspected for damage/wear, parts are lubricated and firearm is reassembled, tested for function and safety. Scope or holographic sight lenses are not cleaned or repaired in any way.


3.  Occasionally Barrels and chambers are heavily encrusted with fouling, rust, or occlusions that cannot be removed by standard cleaning practices. Additional time, approaches, and materials are required to return the barrel /chamber to effective function. Bore and chamber borescope images will be recorder for customer review.


4.  Conservation cleaning is typically conducted on older antique, vintage, collectible arms. Careful assessments are made of the entire firearms condition, noting and areas of damage or decay. Firearms are typically fully disassembled to abate any rust or other decay between the metal and wooden components of the arm. All cleaning is done with non damaging materials and any damage warranting repair (based on the owner's instruction) are repaired maintaining period accuracy and are reversible. Final treatments of wood and metal components applied  to resist further decay are typical museum conservation grade materials.

Scope/Sight Mounting

  • Mount and bore sight rifle scope/optics (1) – $45
  • Mount and bore sight pistol scope/optics (1) –  $45
  • Align crosshairs and/or bore sight an already mounted scope – $15
  • Replace handgun sights (2) – $40
  • Replace shotgun bead(s) (3) – $25
  • Drill and tap shotgun or rifle receiver for Scope/Red Dot bases (1) – $20/hole
  • Range sight in (customer supplies ammo) (4) –  $50


1.  Does not include cost of scope, mounts or rings.


2.  Some handgun sights are factory installed using a press fits with hydraulic presses! ( e.g. KImber) These require considerably more time and effort to remove, a $20 additional charge is assessed in these instances. Note: in some instances the original sights must be cut/destroyed in the process of removal.


3.  Does not include cost of beads/sights. In some instances, the treaded hole is damaged and must be enlarged and rethreaded with a larger size. This process carries and additional $20 charge


4.  Firearm optics will be target sighted to specified range (25, 50, or 100 yds). Client must provide their desired ammunition.Please note customer must fine tune the sighting in of their firearm to achieve optimal accuracy and reproducibility based on their own shooting style, stance and abilities.

General Repair

Standard shop rate of $65/hour is charged to inspect and determine the issues with firearm and complete repairs. If upon inspection it is determined that a firearm cannot be repaired to a functional and safe condition, the customer will be notified. Clients will be notified if parts are required and if parts costs exceed $100, a deposit for the cost of parts and shipping will be required prior to ordering.


Some common repair categories include:


  • Repair/correct cartridge feed, extraction and/or ejection
  • Repair/replace/manufacture damaged or missing parts
  • Smooth and tune firearm action (1)
  • Identify cause and correct firearm firing and/or safety issues
  • Installation of customer specified/provided aftermarket parts (2)
  • Trigger/firing system adjustment/tuning
  • Removal of obstruction from barrel or chamber
  • Install pre-threaded and chambered or short chambered barrels (3)
  • Repair/tune flint or percussion locks
  • Repair/tune single or double set trigger systems 


1.  This consists of de-burring and removing factory manufacturing marks from contact regions of a firearm’s action and polishing contact surfaces to a high finish. In some cases it may be necessary/desirable to replace factory component to improve function of firearm. Shop rate does not include the cost of aftermarket or replacement parts if the client selects this option.


2.  Shop rate does not include the cost of aftermarket or replacement parts. At this time, I do not thread rifle/pistol barrels for the installation of muzzle breaks or suppressors, however I will fit and install/time muzzle breaks or suppressors on a pre-threaded barrel that a customer provides.


3.  This includes any barrel fitted if needed as well as testing and setting headspace when required.Does not include cost of barrel or polishing/bluing (if necessary). I do fit and install drop in or gunsmith fitted aftermarket barrels for pistols as well. 

Stock Repair, Replacement, Refinishing

Wooden stocks are the most commonly damaged components of a firearm. The variables are endless! Dents and scratches are common eyesores, but over many years of use in the field, water infiltration can cause finish delamination and damage of the exposed wood by swelling and decay. People do fall down, drop things and have other “ooops” moments that can cause a stock to crack or break in two or even shatter into fragments. In most cases, these issues can be remedied. Many dents and scratches and even chips and gouges can be repaired and visually eliminated through careful treatment and refinishing…but sometimes a stock will need to be replaced. Many manufacturers still can provide replacement stocks that are either bare wood or factory finished and embellished. Unfortunately, with the demise and dismemberment of so many of our historical arms companies these past few years….parts are drying up. My general practice is to repair and if needed refinish broken stocks, unless a factory replacement can be had at a cost lower than the repair would be. That decision would be made by the customer of course. Each case presents its individual challenges!


Many well loved firearms are brought in by their owners for refinishing. This can be because of typical wear and tear or due to some of the inferior finishing techniques applied by some manufacturers from the start. Many economy grade guns were dipped or sprayed with the equivalent of a gel stain to give an even color on lower grade or unevenly colored stock woods. The Remington Game Master, Wood Master series of hunting arms and Marlin’s Glenfield line from the 1960’s-1980’s are a good examples…they used largely beech or birch wood, not walnut for the stocks! These stocks are subject to flaking off of the finish and if someone tried to touch them up or refinish them with regular stock finish, as you can with walnut…well let’s just say most folks are disappointed with their result. I’ve developed techniques that can provide very satisfying finishes to these stocks…sometimes you can make silk purses from sow’s ears!


Some typical stock related services include:


  • Repair of broken stocks (1) – Standard shop rate $65/hr
  • Replacement and fitting factory stock (2) –  $65
  • Inletting, bedding and finishing semi-inletted wooden/laminate stock (2, 6, 11) – Starting at $250
  • Strip and refinish (Hunter Grade) 1 piece rifle stock or 2 piece shotgun stock (3, 5) – $200
  • Strip and refinish (Gunsmith Grade) 1 piece rifle stock or 2 piece shotgun stock) (4, 5) – $250- 350
  • Gunsmith Grade hand oil finish on unfinished custom or semi-inletted stock – $300
  • Adjust length of pull and install new recoil pad  (6) – $75
  • Refresh/recut worn checkering – Simple pattern $95-120/panel, Complex pattern  $175-200/panel (7)
  • Checkering new/uncheckered stocks – – Standard shop rate $65/hr
  • Two point bedding of action to stock (8) – $150
  • Full action bedding of action to stock (9) – $200
  • Full length barrel and action bedding – $300
  • Free float barrel and seal barrel channel – $120
  • Install Pillar beds (10) – $135
  • Install sling swivels (11) – $40


1.  If possible, repairs will be made such that refinishing of stock will not be required, however some case will require the additional costs of stock refinishing.


2.  Does not include the cost of stock.


3.  For a Hunter Grade finish, the stock is stripped, sanded and refinished with multiple coats of a satin oil-based finished. Dents and scratches are not removed.


4.  For a Gunsmith Grade finish, the stock is stripped, all dents and scratches are removed or minimized as much as possible. Stocks are sanded to a minimum 320 grit and pores are sealed. Wood receives a hand rubbed oil finish to a satin or high luster (client preference).


5.  Some gunstocks are manufacturer finished with various forms of polyurethane or epoxy-like sprays or dips (e.g. Japanese made Brownings, Weatherby, etc). These finishes often chip and flake, however are a bear to remove and a $65 surcharge is applied for these types of stocks.


6.  Does not include cost of recoil pad.


7.  Only hand or rotary cut factory checkering can be refreshed. Stamped checkering as seen on some economy level rifles and shotguns cannot be refreshed, but depending on style, can be cut anew. Areas of checkering that have been excessively worn and abraded may not be recoverable.


8.  Two point bedding will address the recoil lug recess and forward action screw region and extend approximately 1 inch forward of the end of the receiver and well as the contact region of the rear action screw and tang of receiver.


9.  Full action bedding includes the stock-action contact ares extending approximately 1 inch forward of the end of the receiver through the contact region of the rear action screw.


10. Does not include the cost of the pillars.


11. Does not include the cost of swivel sets.


I do not routinely offer spray polyurethane, marine epoxy, or painted finishes.

Metal Repairs, Refinishing and Bluing

A fact that has always plagued gun owners is that Steel Rusts! 


Any firearm that receives normal usage at the range and in the field will in time develop scratches, nicks, or the curse of sweaty hands and begin to rust. As soon as the factory finish on a metal component is breached and bare metal is exposed, oxidation begins. This is true for aluminum components, as well as iron and steel. 


I’ve had firearms come in that were “safe queens”, as some folks call them, that are handled with kid gloves and pampered, only to have the conditions inside the gun safe create an environment that wreaks havoc on the polished surfaces. I’ve also had guns come in that had been in the bed of a pickup for 10 years…use your imagination! Metal components of a firearm are generally more difficult to bring back to a factory finish when rust begins to consume the steel and cause pitting. Some thin parts can rust to the point of crumbling. When a client comes in wanting to have metal refinishing on their firearm done, considerable time is often spent managing expectations and discussing options if metal erosion is extensive. I’ll likely discuss this in a blog sometime.


One other consideration that needs to be addressed is that many firearms are made with a combination of steel, aluminum and plastic parts. Needless to say, only steel components can be blued! Aluminum, other alloys (aka pot metal) and plastics can be refinished using other approaches. There are several kits for aluminum gun part refinishing on the market, and after having seen the results of these (when clients bring me their guns to see if I can remedy the mess) I only go with Cerakote finishing on these components as well as other components that cannot be blued. To date, the results have been spectacular. New Cerakote colors have been developed that match hot caustic blueing results perfectly. An additional advantage to Cerakote is that on deeply pitted steel parts that defy bluing, the metal is sealed and no further rusting can occur.


Hot Caustic bluing is the standard metal finishing method used by the firearms industry. I no longer perform this service in-house, however I have contracted with an excellent bluing service that specializes in this process. I will disassemble and ship the components requiring bluing to them. After the finished items are returned, I reassemble and perform function and safety checks on the firearm. The pricing below reflects my labor and materials and  costs for this service. Shipping /Insurance costs are not included in these prices:


  • Bolt action rifle or shotgun (Hunter Grade)(1) - $250
  • Bolt action rifle or shotgun (Gunsmith Grade)(2) - $290
  • Pump action or automatic Rifle or Shotgun (Hunter Grade)(1, 3) - $270
  • Pump action or automatic Rifle or Shotgun (Gunsmith Grade)(2, 3) - $330
  • Lever action rifle/ shotgun (Hunter Grade)(1) - $300
  • Lever action rifle/shotgun (Gunsmith Grade)(2) - $375
  • Revolver or semiautomatic pistol (Hunter Grade)(1) - $245
  • Revolver or semiautomatic pistol (Gunsmith Grade)(2) - $285
  • Slow Rust Bluing - See below.
  • Cerakote - See below.


1.  For a Hunter Grade finish, surface rust and existing bluing is removed from  all originally blued components and blued using a hot caustic bluing  process. Note: parts do not receive extensive polishing and scratches and  pits in the metal surface are not addressed. 


2.  For  a Gunsmith Grade finish, existing bluing, rust, scratches and pits removed from all originally blued components. Metal surfaces are polished to a  320-400 grit luster and blued using a hot caustic bluing process. Note: It may not be possible to remove deeply eroded pits and scratches from heavily damaged surfaces.


3.  Some  early shotguns such as the Browning A5, its offspring, the Remington Model 11, Mauser rifles and other firearms from the mid-20th century were highly complex with a many small parts requiring greater disassembly and handling time. These firearms  will be assessed a $50 additional charge for services.


Note: Both the Hunter Grade and Gunsmith Grade finish can be had in a non-reflective Matte Finish great for hunting or "tactical" arms at no additional cost. Any firearm component that comes in for refinishing that already has matte surfaces will have those surfaces finished in this same manner.


Slow Rust Bluing is a historical process by which the steel surfaces were blued before the advent of high temperature caustic bluing method was developed for mass production. This process is time consuming and can take up to 2-3 weeks to complete once started to get the desired luster and color. Double guns typically have soldered barrels that cannot be blued using hot caustic bluing. These firearms were originally slow rust blued and the result is a deep, translucent blue, as was seen on these fine old guns. Many of the premier riflesmiths of the past century, such as Adolf Niedner and others produced their masterpiece firearms using this centuries-old method...it's my personal favorite as well!


  • Preparation of metal components  and performing Slow Rust Bluing  - Starts at $500.


Cerakote is a ceramic based finish that is available in myriad colors and patterns, but certain colors such as Elite Blackout are a spot-on match for the hot caustic blue finish used by manufacturers since the 1940's. It is a great option for firearms that have aluminum components, such as shotgun receivers, trigger guards and other alloy parts. Due to its relatively low temperature processing, Cerakote can even be used to refresh the luster on plastic trigger guards and other components when factory replacements are not available. I do not perform Cerakoting in my shop but have a relationship with Kentucky's premier Cerakote specialist Rick Kerr at Kentucky Gun Coatings (KGC). Very often clients have guns that need to have some components blued and other parts Cerakoted. As with standard bluing, I prepare the metal components and ship the relevant parts to the respective vendors. Refer to the price schedule above for estimates of costs.


I do not do metal plating, nitride coating, or color case hardening in my shop, but can facilitate having that done for you if needed.

Copyright © 2025 jvpgunsmith.com - All Rights Reserved

 Terms & Conditions

Privacy Policy

  • Home

Powered by

This website uses cookies.

We use cookies to analyze website traffic and optimize your website experience. By accepting our use of cookies, your data will be aggregated with all other user data.

Accept